Wood veneer sheet Angsana Red

A4 size (210mm x 297mm) natural wood veneer sheet
◉A sheet of natural wood and industrial Japanese paper which are bonded together and can be easily cut with scissors or a cutter.
◉The sheet can also be ironed on at home.

Sheet thickness: approx. 0.25mm

This wood type is available in straight grain, cross grain,


［Wood type］
Wood type：Padoauk
Family:Leguminosae
Place of origin：Southeast Asia
Specific gravity:0.81～0.9
Color：Red
There are a variety of individual variations in color from light orange to deep red. Many of the red strains of wood are brightly colored and are useful for color expression by wood inlay. The wood is heavy and hard. Other names: Padoauk、Burmese Rosewood、Pradoo、amboyna

［EXAMPLE OF USE］
◉FOR EDGES OF WOODEN FURNITURE, ETC.
Curly maple is the most beautiful type of hard maple and is called curly maple. The bird's-eye pattern is also called bird's-eye maple.
By attaching Japanese paper to the back side of a veneer sheet, it becomes easier to use.
◉AS REPAIR MATERIALS
This veneer sheet can be used for repairing and applying to flat wooden surfaces such as furniture and interior decorations.
Please flatten the surfaces of the base with sandpaper so that there are no uneven parts before use.
◉WOODEN INLAY/MARQUETRY
When it is used for wood inlaying/marquetry, the use of wood veneer sheet, which is affixed with Japanese paper, allows for delicate processing. This is because it is relatively easy to arrange, even for smaller and delicate cuts.
◉SPEAKERS
It can be used on laminated boards for speaker boxes, such as plywood, MDF, etc.

［ABOUT IRONING ］
It can be applied with a household iron.
We recommend the use of a special glue that can be applied to the base material (the object to which the veneer is affixed) and used after it dries.
This allows you to apply the wood veneer sheet after the glue has dried, so unlike ordinary glues, you can apply it without being restricted by time.
詳しくはPlease see the video on how to paste.

［wood adhesive (for application of wood veneer sheets by iron)］
CH7WN　CH7WN Vinyl acetate resin-based emulsion type adhesive by KONISHI Co.
F☆☆☆☆

・500g　To purchaseClick here

・1kg   　To purchaseClick here

[How to Use]

1. Apply the Adhesive
   Apply the adhesive evenly to both the surface to be bonded (the base material) and the back of the wood veneer.
   Allow it to dry completely until the white adhesive becomes transparent.
   Approximate amount needed:
• About 10g per 30×30cm area (one side)
• About 20g total for both surfaces
  Note: Amount may vary depending on application method.
2. Bonding (Heat with Iron)
   Once the adhesive is dry, press with a household iron to activate the bonding.
   The adhesive melts at around 80°C (176°F), allowing reactivation even if some time has passed after drying.
   However, it is recommended to complete the bonding process on the same day.
3. How to Use the Iron
• Start with a low temperature and gradually increase as needed.
• Excessive heat may scorch the wood veneer.
• It is generally safe to place the iron directly on the veneer, but using a thin cloth (e.g., a cotton hand towel) helps prevent burns or scratches.
• Do not leave the iron in one spot, even with a cloth — this can cause discoloration or scorching.
• For first-time users, starting at around 100°C (212°F) is safer.
  Note: If the temperature is too low, proper bonding may not occur. Be sure to apply sufficient heat.
4. Finishing & Repairs
   If air bubbles appear under the veneer after bonding, pierce the area with a fine needle or craft knife to release the air, then reheat with the iron. This usually resolves the issue.

[Frequently Asked Questions]

Q: Can I apply it to curved surfaces?
A: It can be applied to two-dimensional curved surfaces. However, ironing may be more difficult. For spherical or complex three-dimensional shapes, wrinkling may occur.

Q: Can I order custom sizes?
A: Yes, we can produce custom sizes up to 1200mm × 2400mm or 900mm × 3000mm.
Note that materials may shrink slightly due to heat during processing. We typically produce pieces about 10mm larger than the actual dimensions to allow for adjustment.

［Notes on purchase］
◉Please note that the light color of the wood veneer often allows the pattern of the underlying surface to show through.
◉Please understand that the wood grain pattern and color may vary slightly from what is shown in the picture.
◉We cannot accept returns or exchanges due to color, pattern or image differences.
◉If you have any special requests for the grain of the wood, please write them down in the remarks box of your order.

［販売元］
• Company : MORIKOUGEI
• Establishment(Of a business): 1953
• Establishment : 1970 6/10
• Capital stock : ￥5,000,000
• CEO :KENICHI MORI
• Number ofEmployees : 3
• Main equipment: Guillotine, gluing machine, hydraulic hot press, wide belt sander, cutting plotter
• Business Description: Manufacture and sale of laminated wood veneer, wood inlay processing, planning/manufacturing and sale of wooden furniture and wooden miscellaneous goods, planning/manufacturing and sale of novelties, exporting and sale of products, manufacturing and sale of arts and crafts.
• Address : 3-5-34 Suehiro Tokushima-shi Tokushima-Ken 770-0866 Japan
• Tel : 088-653-7518
• FAX : 088-626-3773
• MAIL : info@mori-kougei.com

For more information, Please contact us